Now all of the optional baffles are removed.This article was written by the It Still Works team, copy edited and fact checked through a multi-point auditing system, in efforts to ensure our readers only receive the best information. I am new to the forum and I would like to know what would happen if i remove the baffles from the stock exhaust of a vstar classic 650. The bolt to remove the slip on muffler is located just under the passenger foot peg, and can be removed with the socket wrench. Free shipping on many items | Browse your favorite brands | affordable prices. You have to take a long and thick screwdriver and hit it with a hammer on the outside end of the baffle. How Do I Drill Out the Baffels in my 2007 Yamaha V-Star?
Before 06 and after 06 have very different pipes and have to be handled differently.
There is a web site out there that tells you step by step how to drill out the baffles on a Star V1100. Thanks
Get the best deals on Motorcycle Exhaust Pipes for Yamaha V Star 250 when you shop the largest online selection at eBay.com. Pull out the packing material, then put the extended length drill bit into the drill.
When I had my stock pipes I drilled out the baffles from my mufflers like you're thinking about doing. Great sound improvement and likely no rejetting, since the back pressure changes little if any, and I haven't done anything with the intake. Nice Gibbo, and good explanations. Slip On Mufflers.
Thanks to everyone who helped me. Cutting the baffles out of the exhaust pipes on your motorcycle is one of the most common and least expensive modifications that you can make, especially in lieu of purchasing aftermarket pipes. I will be drilling my good mufflers to replace the scratched ones unless I break down and buy an aftermarket set.
This really is a great modification if your on a tight budget like me. To me it doesn't sound that much louder.and agree would not do permanent damage
Step 1. If you want more sound you can just run a drill bit through it. I finally got everything out and I love the new sound. Allowing the engine to breathe easier is always a good thing.
There is another baffle further back along the exhaust pipe, but you don't want to remove it entirely.
Be careful to avoid heating the metal too much, as overheated metal could discolor the chrome muffler housing.Place the hole saw bit into the electric drill and cut the flat metal plate from the exhaust tube. And the best thing about it is that you don't have to re-jet your carbs. I say go for it
It has slightly deep and louder note than stock.
How to...before and after... ah I wouldn't do a permanent scar to my pipes.
The exhaust assembly in a Yamaha V-Star contains a series of baffles and small exhaust pipes that quiet down the sound of the exhaust -- but not everyone prefers a quiet bike. To submit your questions or ideas, or to simply learn more about It Still Works, Avoid removing the baffles of a motorcycle in a town or city in which noise ordinances are enforced, or if you ride primarily at night through residential areas.
Wound up buying DG Hardkrome performance exhaust and rejetting the carbs, shimming up the needles, drilling out pilot screw plugs, dialing them in and got it to sound great.
So far I am leaning towards keeping the gutted mufflers, really sounds great. Find. How did you do it? How to Cut the Baffles Out of My Yamaha V-Star Pipes Step 1.
Insert the hole saw into the end cone on the exhaust, which is the exhaust tip, and drill out … Reply. I am stuck the same way you were.
And I think a lot of riders like a good sounding output.
These are not like aftermarket pipes that you can put the baffle back in. This is the part which will be removed.Insert the metal grinding bit into the drill and grind away the weld on the outside of the flat metal plate. Insert the hole saw into the end cone on the exhaust, which is the exhaust tip, and drill out the end cone with the hole saw.
I'll keep trying... My wife swears that I am doing this as a ploy to get her to give in and say just go get the exhaust that you want.